eMMC Pro V1.06 Notes :
| Error Messages and Handling ; | |||
| CMD_CRC_FAIL | = | (1) | which is Command response received (but CRC check failed) |
| DATA_CRC_FAIL | = | (2) | which is Data bock sent/received (CRC check Failed) |
| CMD_RSP_TIMEOUT | = | (3) | which is Command response timeout |
| DATA_TIMEOUT | = | (4) | which is Data time out |
| TX_UNDERRUN | = | (5) | which is Transmit FIFO under-run |
| RX_OVERRUN | = | (6) | which is Receive FIFO over-run |
| START_BIT_ERR | = | (7) | which is Start bit not detected on all data signals in widE bus mode |
| CMD_OUT_OF_RANGE | = | (8) | which is CMD's argument was out of range |
| ADDR_MISALIGNED | = | (9) | which is Misaligned address |
| BLOCK_LEN_ERR | = | (10) | which is Transferred block length is not allowed for the card or the number of transferred bytes does not match the block length |
| ERASE_SEQ_ERR | = | (11) | which is An error in the sequence of erase command occurs |
| BAD_ERASE_PARAM | = | (12) | which is An Invalid selection for erase groups |
| WRITE_PROT_VIOLATION | = | (13) | which is Attempt to program a write protect block |
| LOCK_UNLOCK_FAILED | = | (14) | which is Sequence or password error has been detected in unlock command or if there was an attempt to access a locked card |
| COM_CRC_FAILED | = | (15) | which is CRC check of the previous command failed |
| ILLEGAL_CMD | = | (16) | which is Command is not legal for the card state |
| CARD_ECC_FAILED | = | (17) | which is Card internal ECC was applied but failed to correct the data |
| CC_ERROR | = | (18) | which is Internal card controller error |
| GENERAL_UNKNOWN_ERROR | = | (19) | which is General or Unknown error |
| STREAM_READ_UNDERRUN | = | (20) | which is The card could not sustain data transfer in stream read operation. |
| STREAM_WRITE_OVERRUN | = | (21) | which is The card could not sustain data programming in stream mode |
| CID_CSD_OVERWRITE | = | (22) | which is CID/CSD overwrite error |
| WP_ERASE_SKIP | = | (23) | which is only partial address space was erased |
| CARD_ECC_DISABLED | = | (24) | which is Command has been executed without using internal ECC |
| ERASE_RESET | = | (25) | which is Erase sequence was cleared before executing because an out of erase sequence command was received |
| AKE_SEQ_ERROR | = | (26) | which is Error in sequence of authentication. |
| INVALID_VOLTRANGE | = | (27) | |
| ADDR_OUT_OF_RANGE | = | (28) | |
| SWITCH_ERROR | = | (29) | |
| SDIO_DISABLED | = | (30) | |
| SDIO_FUNCTION_BUSY | = | (31) | |
| SDIO_FUNCTION_FAILED | = | (32) | |
| SDIO_UNKNOWN_FUNCTION | = | (33) | |
| Standard errors and messages ; | |||
| INTERNAL_ERROR | = | (34) | |
| NOT_CONFIGURED | = | (35) | |
| REQUEST_PENDING | = | (36) | |
| REQUEST_NOT_APPLICABLE | = | (37) | |
| INVALID_PARAMETER | = | (38) | |
| UNSUPPORTED_FEATURE | = | (39) | |
| UNSUPPORTED_HW | = | (40) | |
| ERROR | = | (41) | |
| OK | = | (42) | |
| CMD1_TIMEOUT | = | (60) |
Download : eMMC Pro V1.06 Latest.rar
